日本積水流感病毒檢測試劑盒

廣州健侖生物科技有限公司

廣州健侖長期供應各種流感檢測試劑，包括進口和國產的品牌，主要包括日本富士瑞必歐、日本生研、美國BD、美國NovaBios、美國binaxNOW、凱必利、廣州創侖等主流品牌。

日本積水流感病毒檢測試劑盒

我司還提供其它進口或國產試劑盒：登革熱、瘧疾、流感、A鏈球菌、合胞病毒、腮病毒、乙腦、寨卡、黃熱病、基孔肯雅熱、克錐蟲病、違禁品濫用、肺炎球菌、軍團菌、化妝品檢測、食品安全檢測等試劑盒以及日本生研細菌分型診斷血清、德國SiFin診斷血清、丹麥SSI診斷血清等產品。

歡迎咨詢

歡迎咨詢2042552662

想了解更多的產品及服務請掃描下方二維碼：

【公司名稱】 廣州健侖生物科技有限公司
【市場部】    楊永漢

【】 
【騰訊  】 2042552662
【公司地址】 廣州清華科技園創新基地番禺石樓鎮創啟路63號二期2幢101-103室

（六）包埋（埋蠟、沉床）
材料浸蠟后再換兩次已熔融的純蠟，然后將材料和石蠟一起倒入提前疊好的包埋紙盒中，用加熱的鑷子迅速將材料按一定的間隔和所需的切面擺放整齊，同時用加熱的鑷子趕走材料周圍的氣泡，待紙盒表面的石蠟?zāi)毯髮⒓埡衅椒湃肜渌校故炑杆倌獭ui后從紙盒中取出蠟塊，以便保存。注意將樣品編號封于蠟塊上，以免樣品混淆。
（七）修塊
將已包埋好的蠟塊切成小塊，每一小塊包含一塊材料。然后按照所需的切面，用單面刀片將小蠟塊切成梯形，并可粗視到材料切面。然后用燒紅的蠟鏟把蠟塊底部牢固的粘接在載蠟器上。
（八）切片
用切片機（如旋轉切片機）將蠟塊切成連續的蠟帶。切片時先把切片刀夾在刀架上，再把載蠟器夾在固定裝置上（注意安裝切刀的角度，刀口運行方向與材料切面平行），然后調整好所需厚度，一般可在7~14微米，視材料和所需觀察對象而定，一般葉片、芽可厚些，胚囊和花粉粒可薄些，轉動切片機切片。

(F) embedded (buried wax, bed)
The material is immersed in wax and the molten wax is changed twice more. The material and paraffin are then poured into pre-folded embedding cartons, and heated tweezers are used to quickly place the material at regular intervals and the desired cut Tidy, while using heated tweezers to get rid of the bubbles around the material until the carton surface of the paraffin wax flat after the flat into the cold water, the paraffin wax quickly solidified. Finally, remove the wax block from the paper tray to save. Note that the sample number is sealed on the wax block to avoid sample confusion.
(Seven) repair block
The embedded wax blocks are cut into small pieces, each piece contains a piece of material. Then cut the small wax block into a trapezoid with a single-sided insert, as desired, and glancing to the material cut surface. Then use a red wax spatula to stick the bottom of the wax block firmly to the wax carrier.
(Eight) slice
Use a microtome (such as a rotary microtome) to cut the pieces of wax into continuous wax strips. Slice the first blade clip on the turret, and then clip the wax holder fixed device (pay attention to the angle of the cutter installation, knife edge running direction parallel to the material section), and then adjust the desired thickness, usually in the 7 ~ 14 microns, depending on the material and the desired object of observation, the general leaves, buds can be thicker, embryo sac and pollen grains can be thin, turn the slicer slice.